Bike test: Cube Hyde Race city hybrid
Bike test: Cube Hyde Race city hybrid
Cube calls the Hyde Race a city bike. Does that mean cruising along the car-free boulevards of some imagined mainland-European cycling paradise, or the rather different experience of the British urban commuter, enduring foul weather, indifferent drivers and intermittent infrastructure?
Either way, the ‘Race’ part of the Cube’s moniker is misapplied. While it might have the edge on a Boris Bike, it wouldn’t be the choice of even mildly competitive city cyclists; it isn’t very fast.
Frame and fork
Instead, it’s a sturdy machine built around a seemingly bomb-proof aluminium frame and fork with meaty but regular welds. It’s a handsome beast, its satin black paint accented with vivid green highlights. While it’s unusually spartan for a European hybrid, it does have mounts for mudguards and racks front and rear so can be equipped for duties ranging from laden touring to light commuting.
The frame is built using double-butted ‘Superlight Urban’ aluminium tubing. It’s stiff enough both torsionally and laterally to satisfy most urban cyclists. Indeed, there’s not much frame flex in any plane, and Cube’s engineers clearly did a fine job of accommodating the split in the drive-side rear triangle needed to take an non-separable drive belt.
Cube calls it Split and Slide. There’s a sliding dropout on both sides to allow for belt tension adjustment; the non-drive side slider doubles as the mount for the rear disc brake calliper, while an extra bolt securing the drive side slider also clamps together the ends of the seat stays and chain stays to create a rigid single structure.
It’s a neat arrangement, if a little industrial. Less neat is the front brake cable, zip-tied to the back of the fork leg.
Stopping comes courtesy of Shimano hydraulic discs front and rear. With opposed pistons and effective pad return springs, the BR-315 callipers offer crisp, drag-free performance. Brake feel is a little wooden and lacking in initial bite, but as may be expected there’s enough power when they are squeezed hard.
Unlikely to need much maintenance beyond pad replacement for a couple of seasons, they certainly fit the Cube’s design brief.
The same might be said for the Alfine rear hub. It’s a marvel of robust, cost-effective engineering that’s perhaps slightly wasted on urban riding, where the entirety of the gear range (over 300%) is rarely likely to be needed.
The hub shifts without appreciable resistance both at a standstill and under power. The gearing range, from 30in to 92in, is well-chosen for general riding but might prove a little high for heavy loads or steeper hills.
Belt drive means it’s not that easy to alter, should one wish to do so. The Cube runs a Gates Carbon Drive CDN belt. Introduced in 2015, the CDN is a lower-cost alternative to the ‘full-fat’ CDX Centertrack system and is intended for ‘lower-mileage pavement and city bikes’.
The CDN belt has fewer carbon cords, and it features a tooth profile optimised, apparently, for lower tension. The system includes a steel rear sprocket and fibre-reinforced composite chainwheel on the Gates-branded square-taper-axle chainset.
To keep the belt properly engaged with the sprockets, it is installed under permanent tension rather than set up with a small amount of slack as per a chain. This inherent tension adds to bearing friction losses, which can be detected when rotating the cranks backwards but can’t really be felt from the saddle; Gates claims overall efficiency equivalent to a new chain transmission.
The feedback through the pedals is different, but is perfectly acceptable even under hard pedalling effort.
The big benefit of a belt drive is the need for almost no maintenance even in the adverse conditions that would quickly kill a chain. Other benefits include a long service life, with no efficiency drop-off or need to re-adjust belt tension along the way; cleanliness; and low weight.
The only obvious question concerns ease of rear wheel removal. This is made no easier by the Alfine hub’s ‘cassette joint’, which connects the control wire. The cable routing of the new SG-S7000 8-speed Alfine is reversed, so that the inner wire runs onto the cassette joint ring from the top.
Re-fitting the control wire after wheel installation is said to have been made easier, and it’s now no big deal if you have the knack.
But what’s it like to ride? It’s a long way off the ground. The fat tyres – seriously treaded 700×42C Schwalbe Road Cruisers – need a substantial bottom bracket drop and don’t have it, the 70mm figure being better suited to 23C tyres. The tyres roll well, give a fairly supple ride and look suited to the towpath or gravel, but at over 700g each do nothing for acceleration.
Factor in power lost to the hub and belt, and the bike is no match on speed for a well-maintained derailleur-geared machine. If anything, it is today’s version of a utility roadster – think Raleigh Tourist Deluxe or early Hercules Balmoral – but with discs, Alfine and Gates belt in place of roller brakes, three-speed Sturmey Archer hub, and enclosed chain case.
Unfortunately, without mudguards it loses marks on the utility front, but these can be added.
First published in Cycle magazine, December 2016/January 2017 issue. All information correct at time of publishing.
Our test promise
At Cycling UK and Cycle magazine, we are proudly independent. There’s no pressure to please advertisers as we’re funded by our members. Our product reviews aren’t press releases; they’re written by experienced cyclists after thorough testing.
Sizes: 46, 50, 54 (tested), 58, 62cm
Frame & fork: Aluminium Superlite Urban double butted, with aluminium rigid fork
Wheels: 42-622 Schwalbe Road Cruiser Active tyres, Cube UX24 rims, 32 spokes front and rear, Shimano Deore HB-M615 Centerlock disc mount front hub, Shimano Alfine SG-S700 8-speed rear hub
Transmission: Gates S150 CDN 46t crankset, 170mm crank arms with Thun square-taper BB; Gates CDN 111t drive belt; Shimano Alfine SL-S700 shifters, Shimano Alfine SG-S700 eight-speed geared hub. 8 ratios, 30-92in
Braking: Shimano BR-M315 hydraulic disc brakes, 160mm rotors
Steering & seating: Cube Flat Race 660mm handlebar, Cube Performance Stem Pro 31.8mm stem; Cube Natural Fit Tour grips; FSA No 10 semi- integrated 1 1/8” headset, Selle Royal Prestige saddle, Cube Performance Post seatpost 27.2mm with Cube Screwclamp
The 8-speed version of Pashley’s classic steel roadster has hub brakes, an enclosed chain case, mudguards, rack… and serious retro style.
Similar to the Hyde Race, this belt-drive Marin has an 8-speed hub, disc brakes, a 6061 aluminium frame, and sleek styling.